Allumer
- 1Press 전원 (bottom right).
- 2The 운전 light comes on when the boiler is allowed to run.
Kiturami NCTR-6000 expliqué
A Kiturami controller with three knobs on the left (room temp, hot water, timer) and four round buttons on the right.
À quoi sert chaque bouton ?
- 1Status screen · 상태표시부sangtae pyosibuLights the active mode word (난방, 목욕, 예약, 외출, 취침, 온수, 점검) and shows temps or error codes.
- 2Running light · 운전unjeonLights when the boiler is allowed to run in the current mode.
- 3Heating knob · 난방 다이얼nanbang daieolSets the room temperature, marked 10 … 25 … 45°C. Turn fully left past 10 into 외출 for away / frost protection.
- 4Away zone (on heating knob) · 외출oechulThe curved zone left of 10. Knob here = away mode: minimum heat to stop freezing.
- 5Heating button · 난방nanbangSelects normal heating. Also the UP key inside setting menus.
- 6Hot-water knob · 온수 다이얼onsu daieolHot tap temperature: 저온 (low) … 중온 (medium) … 고온 (high), about 35–60°C. The number flashes on screen while you turn it.
- 7Hot water / Bath button · 온수onsuBath boost: lots of hot water, returns to the previous mode after 2 h 30 min. (The manual calls this the 목욕 button.)
- 8Sleep · 취침chwichimNight saving: keeps a moderate temperature, then returns to normal room mode after 5 h 30 min. Also the DOWN key inside menus.
- 9Timer knob · 예약 다이얼yeyak daieolSets how long the boiler RESTS between runs: 0 … 7 hours (from 10 min up). Run time per cycle is set separately (5–60 min).
- 10Power · 전원jeonwonOn/off. Also restarts the boiler after an error (3 tries in a row, then wait 5 min).
Quel réglage choisir ?
Winter: 난방 button, heating knob at about 22, 예약 knob at 0, 온수 knob at about 42°C (between 저온 and 중온). Nights: optional 취침. Out for days: knob into 외출.
Comment… ?
Chauffer la pièce à une température
- 1Press 난방 (top right button).
- 2Turn the 난방 knob to about 22 — a bit left of the 25 mark at the top.
- 3Make sure the 예약 knob (bottom) is at 0 so the timer is not interrupting heating (inferred, see notes).
Mode sol (ondol)
- 1Setup step — normally done once by the installer.
- 2Press 전원 so the controller is OFF.
- 3Turn the knobs: 난방 to 45°C, 온수 to 고온, 예약 to 7시간.
- 4Hold 난방 about 5 s until S1 or S2 shows. Use 난방 (up) / 취침 (down) to choose S2 = floor mode. It saves after 5 s.
- 5To set the floor-water temp (45–85°C): hold 취침 about 5 s; while it flashes use 난방 (up) / 취침 (down). Saves after 5 s.
Partir quelques jours
- 1Turn the 난방 knob all the way left into the 외출 zone.
- 2Leave power ON and the gas valve open.
- 3In a hard freeze set the knob to 10–15 instead (manual advice). The timer does not work while in 외출.
Programmer
- 1Turn the 예약 knob to how long the boiler should REST: 10 min up to 7 hours.
- 2Run time per cycle: hold 난방 about 5 s; while it flashes set 5–60 min with 난방 (up) / 취침 (down).
- 3Example: 2 h rest + 20 min run, repeating. Timer is ignored while the heating knob is in 외출.
Eau chaude seule (été)
- 1No dedicated summer button on this model.
- 2Turn the 난방 knob to 외출: heating only runs to prevent freezing, and hot water still works in 외출 (manual).
Régler l'eau chaude
- 1Turn the 온수 knob. The setting flashes on the screen.
- 2Aim for about 42°C — just left of 중온. Range 35–60°C.
- 3For a bath, press the 온수 button (bath boost, 2 h 30 min).
Éteindre
- 1Press 전원. In winter use the 외출 position instead.
Que signifient les mots à l'écran ?
| 난방 | Heating | Normal room heating is on. |
|---|---|---|
| 취침 | Sleep | Night saving, auto-returns after 5 h 30 min (lit in photo 70). |
| 예약 | Timer | Repeat timer is on. |
| 온수 | Hot water | Hot-water setting shown/active. |
| 목욕 | Bath | Bath boost, 2 h 30 min. |
| 외출 | Away | Frost protection. |
| 점검 | Check | Boiler needs checking — an error code is showing. |
| number (e.g. 19) | Temperature | Current room temp, or the setting you are changing (flashes). |
| S1 / S2 | Heating method | Only in the setup menu: S1 = room-sensor mode, S2 = floor (온돌) mode. |
Les pièges de ce modèle
- Turning the 난방 knob too far left goes past 10 into 외출 — heating mostly stops.
- The button printed 온수 is the BATH boost (manual calls it 목욕) — it does not set the hot-water temperature; the 온수 KNOB does.
- 취침 (sleep) turns itself off after 5 h 30 min and goes back to room mode.
- The 45°C at the end of the heating knob is the top of the room-temp scale — you never need it except in the setup menu.
- If the 예약 knob is not at 0, the boiler may pause for hours (inferred).
Un code erreur s'affiche ?
When 점검 lights, an error code shows in the number area. Press 전원 off/on to restart (3 tries max, then wait 5 min). If it returns, call 1588-9000 with the code.
Service après-vente (coréen) : 1588-9000
