์ผ๊ธฐ
- 1Press the power button (bottom-left, โป symbol).
Kiturami NRS-1000HD ์์ด ์ค๋ช
A Kiturami room-by-room (๊ฐ๋ฐฉ) controller: one screen shows the living room (๊ฑฐ์ค) and rooms 1โ3, with buttons for mode, timer on/off, up/down and power.
์ด ๋ชจ๋ธ์ ์ค๋ช ์๋ฅผ ์ฐพ์ง ๋ชปํด ๊ฐ์ฅ ๋น์ทํ ๋ชจ๋ธ ๊ธฐ์ค์ผ๋ก ์ ๋ฆฌํ์ด์. ๋ค๋ฅด๊ฒ ์๋ํ๋ฉด ์ฌ์ง์ ๋ณด๋ด์ฃผ์ธ์.
๊ฐ ๋ฒํผ์ ๋ฌด์จ ๊ธฐ๋ฅ์ธ๊ฐ์?
- 1Mode stickers ยท ROOM / TIMER / OUTMODE / HOT WATER(English stickers)Hand-added English labels for the modes the ๊ธฐ๋ฅ button cycles through: room, timer, away, hot water/bath.
- 2Room mode (shown) ยท ์ค๋ดsilnaeCurrent mode of the selected room. Sun icon + ์ค๋ด = heating to a set temperature.
- 3Current temp ยท ํ์ฌ์จ๋hyeonjae ondoTemperature in the selected room (22.0ยฐC here).
- 4Rooms ยท ๊ฑฐ์ค 1 2 3geosil il i sam๊ฑฐ์ค = living room, 1/2/3 = bedrooms. The underlined one is the room you are viewing/changing.
- 5Room select ยท ๋ฐฉ์ ํbang seontaekPrinted over ๊ธฐ๋ฅ and ์์ฝ๊ฐ๋ โ likely press both together to step to the next room (unverified).
- 6Mode ยท ๊ธฐ๋ฅ (MODE)gineungCycles the mode for the selected room: ์ค๋ด (room) โ ์์ฝ (timer) โ ์ธ์ถ (away) โ ๋ชฉ์/์จ์ (hot water/bath).
- 7Timer: run time ยท ์์ฝ๊ฐ๋ (TIMER-ON)yeyak gadongIn ์์ฝ mode, sets how many minutes the heating RUNS each cycle.
- 8Up ยท โฒollimRaises the wanted temp or the value being set.
- 9Power ยท ์ ์jeonwonOn/off for the controller.
- 10Timer: rest time ยท ์์ฝ์ ์ง (TIMER-OFF)yeyak jeongjiIn ์์ฝ mode, sets how many hours the heating RESTS between runs.
- 11Down ยท โผnaerimLowers the wanted temp or the value being set.
์ด๋ค ์ค์ ์ด ์ข๋์?
Your room: ์ค๋ด at 21โ22ยฐC. Empty rooms: ์ธ์ถ. Avoid ์์ฝ unless you know the numbers (about 20 min on / 2 h off).
์ด๋ป๊ฒ ํ๋์?
์ค๋ด ์จ๋ ๋ง์ถ๊ธฐ
- 1Check which room is underlined (๊ฑฐ์ค, 1, 2 or 3). Change room with ๋ฐฉ์ ํ (likely ๊ธฐ๋ฅ + ์์ฝ๊ฐ๋ together โ unverified).
- 2Press ๊ธฐ๋ฅ (MODE) until ์ค๋ด shows.
- 3Press โฒ/โผ to set 22ยฐC. Wait about 10 s and it saves.
๋ฉฐ์น ์ง ๋น์ธ ๋
- 1Press ๊ธฐ๋ฅ until ์ธ์ถ shows. Rooms are only kept from freezing.
- 2Unused rooms can stay in ์ธ์ถ while you heat your own room.
์์ฝ ์ค์
- 1Press ๊ธฐ๋ฅ until ์์ฝ shows.
- 2Press ์์ฝ๊ฐ๋ (TIMER-ON) and set the run minutes with โฒ/โผ (sister model: 5โ60 min, default 20).
- 3Press ์์ฝ์ ์ง (TIMER-OFF) and set the rest hours with โฒ/โผ (sister model: default 2 h).
- 4Wait ~10 s to save.
์จ์๋ง (์ฌ๋ฆ)
- 1Set every room to ์ธ์ถ with ๊ธฐ๋ฅ. Hot water keeps working from the boiler (unverified on this model).
๋๊ธฐ
- 1Press power. In winter, prefer ์ธ์ถ so pipes in each room stay safe.
ํ๋ฉด ๊ธ์๋ ๋ฌด์จ ๋ป์ธ๊ฐ์?
| ์ค๋ด (sun icon) | Room mode | Heats the selected room to its set temp. |
|---|---|---|
| ์์ฝ | Timer | Runs X minutes, rests Y hours. |
| ์ธ์ถ | Away | Frost protection only (sister model: heats only below ~7ยฐC). |
| ๋ชฉ์ | Bath / hot water | Hot-water priority; sister model returns after 2 h 30 min. |
| ํ์ฌ์จ๋ 22.0โ | Current temp | Selected room's temperature. |
| ๊ฑฐ์ค / 1 / 2 / 3 | Rooms | Underlined = room currently shown. |
์ด ๋ชจ๋ธ์์ ์์ฃผ ํท๊ฐ๋ฆฌ๋ ์
- Each room has its own mode and temperature โ make sure the room you are standing in is the one underlined before changing anything.
- The 22.0 on screen is the CURRENT temp of the selected room, not necessarily your room.
- This is a zone controller: the boiler itself may also have its own Kiturami controller elsewhere.
์๋ฌ๊ฐ ๋ ์
No model-specific codes found. Power off/on once; if it repeats, call Kiturami 1588-9000.
A/S: 1588-9000 (not visible in photo; Kiturami national A/S)