์ผ๊ธฐ
- 1Press ์ ์ (bottom right).
- 2The ์ด์ light comes on when the boiler is allowed to run.
Kiturami NCTR-6000 ์์ด ์ค๋ช
A Kiturami controller with three knobs on the left (room temp, hot water, timer) and four round buttons on the right.
๊ฐ ๋ฒํผ์ ๋ฌด์จ ๊ธฐ๋ฅ์ธ๊ฐ์?
- 1Status screen ยท ์ํํ์๋ถsangtae pyosibuLights the active mode word (๋๋ฐฉ, ๋ชฉ์, ์์ฝ, ์ธ์ถ, ์ทจ์นจ, ์จ์, ์ ๊ฒ) and shows temps or error codes.
- 2Running light ยท ์ด์ unjeonLights when the boiler is allowed to run in the current mode.
- 3Heating knob ยท ๋๋ฐฉ ๋ค์ด์ผnanbang daieolSets the room temperature, marked 10 โฆ 25 โฆ 45ยฐC. Turn fully left past 10 into ์ธ์ถ for away / frost protection.
- 4Away zone (on heating knob) ยท ์ธ์ถoechulThe curved zone left of 10. Knob here = away mode: minimum heat to stop freezing.
- 5Heating button ยท ๋๋ฐฉnanbangSelects normal heating. Also the UP key inside setting menus.
- 6Hot-water knob ยท ์จ์ ๋ค์ด์ผonsu daieolHot tap temperature: ์ ์จ (low) โฆ ์ค์จ (medium) โฆ ๊ณ ์จ (high), about 35โ60ยฐC. The number flashes on screen while you turn it.
- 7Hot water / Bath button ยท ์จ์onsuBath boost: lots of hot water, returns to the previous mode after 2 h 30 min. (The manual calls this the ๋ชฉ์ button.)
- 8Sleep ยท ์ทจ์นจchwichimNight saving: keeps a moderate temperature, then returns to normal room mode after 5 h 30 min. Also the DOWN key inside menus.
- 9Timer knob ยท ์์ฝ ๋ค์ด์ผyeyak daieolSets how long the boiler RESTS between runs: 0 โฆ 7 hours (from 10 min up). Run time per cycle is set separately (5โ60 min).
- 10Power ยท ์ ์jeonwonOn/off. Also restarts the boiler after an error (3 tries in a row, then wait 5 min).
์ด๋ค ์ค์ ์ด ์ข๋์?
Winter: ๋๋ฐฉ button, heating knob at about 22, ์์ฝ knob at 0, ์จ์ knob at about 42ยฐC (between ์ ์จ and ์ค์จ). Nights: optional ์ทจ์นจ. Out for days: knob into ์ธ์ถ.
์ด๋ป๊ฒ ํ๋์?
์ค๋ด ์จ๋ ๋ง์ถ๊ธฐ
- 1Press ๋๋ฐฉ (top right button).
- 2Turn the ๋๋ฐฉ knob to about 22 โ a bit left of the 25 mark at the top.
- 3Make sure the ์์ฝ knob (bottom) is at 0 so the timer is not interrupting heating (inferred, see notes).
์จ๋ ๋ชจ๋
- 1Setup step โ normally done once by the installer.
- 2Press ์ ์ so the controller is OFF.
- 3Turn the knobs: ๋๋ฐฉ to 45ยฐC, ์จ์ to ๊ณ ์จ, ์์ฝ to 7์๊ฐ.
- 4Hold ๋๋ฐฉ about 5 s until S1 or S2 shows. Use ๋๋ฐฉ (up) / ์ทจ์นจ (down) to choose S2 = floor mode. It saves after 5 s.
- 5To set the floor-water temp (45โ85ยฐC): hold ์ทจ์นจ about 5 s; while it flashes use ๋๋ฐฉ (up) / ์ทจ์นจ (down). Saves after 5 s.
๋ฉฐ์น ์ง ๋น์ธ ๋
- 1Turn the ๋๋ฐฉ knob all the way left into the ์ธ์ถ zone.
- 2Leave power ON and the gas valve open.
- 3In a hard freeze set the knob to 10โ15 instead (manual advice). The timer does not work while in ์ธ์ถ.
์์ฝ ์ค์
- 1Turn the ์์ฝ knob to how long the boiler should REST: 10 min up to 7 hours.
- 2Run time per cycle: hold ๋๋ฐฉ about 5 s; while it flashes set 5โ60 min with ๋๋ฐฉ (up) / ์ทจ์นจ (down).
- 3Example: 2 h rest + 20 min run, repeating. Timer is ignored while the heating knob is in ์ธ์ถ.
์จ์๋ง (์ฌ๋ฆ)
- 1No dedicated summer button on this model.
- 2Turn the ๋๋ฐฉ knob to ์ธ์ถ: heating only runs to prevent freezing, and hot water still works in ์ธ์ถ (manual).
์จ์ ์จ๋ ๋ฐ๊พธ๊ธฐ
- 1Turn the ์จ์ knob. The setting flashes on the screen.
- 2Aim for about 42ยฐC โ just left of ์ค์จ. Range 35โ60ยฐC.
- 3For a bath, press the ์จ์ button (bath boost, 2 h 30 min).
๋๊ธฐ
- 1Press ์ ์. In winter use the ์ธ์ถ position instead.
ํ๋ฉด ๊ธ์๋ ๋ฌด์จ ๋ป์ธ๊ฐ์?
| ๋๋ฐฉ | Heating | Normal room heating is on. |
|---|---|---|
| ์ทจ์นจ | Sleep | Night saving, auto-returns after 5 h 30 min (lit in photo 70). |
| ์์ฝ | Timer | Repeat timer is on. |
| ์จ์ | Hot water | Hot-water setting shown/active. |
| ๋ชฉ์ | Bath | Bath boost, 2 h 30 min. |
| ์ธ์ถ | Away | Frost protection. |
| ์ ๊ฒ | Check | Boiler needs checking โ an error code is showing. |
| number (e.g. 19) | Temperature | Current room temp, or the setting you are changing (flashes). |
| S1 / S2 | Heating method | Only in the setup menu: S1 = room-sensor mode, S2 = floor (์จ๋) mode. |
์ด ๋ชจ๋ธ์์ ์์ฃผ ํท๊ฐ๋ฆฌ๋ ์
- Turning the ๋๋ฐฉ knob too far left goes past 10 into ์ธ์ถ โ heating mostly stops.
- The button printed ์จ์ is the BATH boost (manual calls it ๋ชฉ์) โ it does not set the hot-water temperature; the ์จ์ KNOB does.
- ์ทจ์นจ (sleep) turns itself off after 5 h 30 min and goes back to room mode.
- The 45ยฐC at the end of the heating knob is the top of the room-temp scale โ you never need it except in the setup menu.
- If the ์์ฝ knob is not at 0, the boiler may pause for hours (inferred).
์๋ฌ๊ฐ ๋ ์
When ์ ๊ฒ lights, an error code shows in the number area. Press ์ ์ off/on to restart (3 tries max, then wait 5 min). If it returns, call 1588-9000 with the code.
A/S: 1588-9000
