Encender
- 1Press 전원 (bottom right).
- 2The 운전 light comes on when the boiler is allowed to run.
Kiturami NCTR-6000 explicado
A Kiturami controller with three knobs on the left (room temp, hot water, timer) and four round buttons on the right.
¿Qué hace cada botón?
- 1Status screen · 상태표시부sangtae pyosibuLights the active mode word (난방, 목욕, 예약, 외출, 취침, 온수, 점검) and shows temps or error codes.
- 2Running light · 운전unjeonLights when the boiler is allowed to run in the current mode.
- 3Heating knob · 난방 다이얼nanbang daieolSets the room temperature, marked 10 … 25 … 45°C. Turn fully left past 10 into 외출 for away / frost protection.
- 4Away zone (on heating knob) · 외출oechulThe curved zone left of 10. Knob here = away mode: minimum heat to stop freezing.
- 5Heating button · 난방nanbangSelects normal heating. Also the UP key inside setting menus.
- 6Hot-water knob · 온수 다이얼onsu daieolHot tap temperature: 저온 (low) … 중온 (medium) … 고온 (high), about 35–60°C. The number flashes on screen while you turn it.
- 7Hot water / Bath button · 온수onsuBath boost: lots of hot water, returns to the previous mode after 2 h 30 min. (The manual calls this the 목욕 button.)
- 8Sleep · 취침chwichimNight saving: keeps a moderate temperature, then returns to normal room mode after 5 h 30 min. Also the DOWN key inside menus.
- 9Timer knob · 예약 다이얼yeyak daieolSets how long the boiler RESTS between runs: 0 … 7 hours (from 10 min up). Run time per cycle is set separately (5–60 min).
- 10Power · 전원jeonwonOn/off. Also restarts the boiler after an error (3 tries in a row, then wait 5 min).
¿Qué ajuste uso?
Winter: 난방 button, heating knob at about 22, 예약 knob at 0, 온수 knob at about 42°C (between 저온 and 중온). Nights: optional 취침. Out for days: knob into 외출.
¿Cómo…?
Calentar la habitación a una temperatura
- 1Press 난방 (top right button).
- 2Turn the 난방 knob to about 22 — a bit left of the 25 mark at the top.
- 3Make sure the 예약 knob (bottom) is at 0 so the timer is not interrupting heating (inferred, see notes).
Modo suelo (ondol)
- 1Setup step — normally done once by the installer.
- 2Press 전원 so the controller is OFF.
- 3Turn the knobs: 난방 to 45°C, 온수 to 고온, 예약 to 7시간.
- 4Hold 난방 about 5 s until S1 or S2 shows. Use 난방 (up) / 취침 (down) to choose S2 = floor mode. It saves after 5 s.
- 5To set the floor-water temp (45–85°C): hold 취침 about 5 s; while it flashes use 난방 (up) / 취침 (down). Saves after 5 s.
Salir unos días
- 1Turn the 난방 knob all the way left into the 외출 zone.
- 2Leave power ON and the gas valve open.
- 3In a hard freeze set the knob to 10–15 instead (manual advice). The timer does not work while in 외출.
Programar
- 1Turn the 예약 knob to how long the boiler should REST: 10 min up to 7 hours.
- 2Run time per cycle: hold 난방 about 5 s; while it flashes set 5–60 min with 난방 (up) / 취침 (down).
- 3Example: 2 h rest + 20 min run, repeating. Timer is ignored while the heating knob is in 외출.
Solo agua caliente (verano)
- 1No dedicated summer button on this model.
- 2Turn the 난방 knob to 외출: heating only runs to prevent freezing, and hot water still works in 외출 (manual).
Ajustar el agua caliente
- 1Turn the 온수 knob. The setting flashes on the screen.
- 2Aim for about 42°C — just left of 중온. Range 35–60°C.
- 3For a bath, press the 온수 button (bath boost, 2 h 30 min).
Apagar
- 1Press 전원. In winter use the 외출 position instead.
¿Qué significan las palabras de la pantalla?
| 난방 | Heating | Normal room heating is on. |
|---|---|---|
| 취침 | Sleep | Night saving, auto-returns after 5 h 30 min (lit in photo 70). |
| 예약 | Timer | Repeat timer is on. |
| 온수 | Hot water | Hot-water setting shown/active. |
| 목욕 | Bath | Bath boost, 2 h 30 min. |
| 외출 | Away | Frost protection. |
| 점검 | Check | Boiler needs checking — an error code is showing. |
| number (e.g. 19) | Temperature | Current room temp, or the setting you are changing (flashes). |
| S1 / S2 | Heating method | Only in the setup menu: S1 = room-sensor mode, S2 = floor (온돌) mode. |
Trampas de este modelo
- Turning the 난방 knob too far left goes past 10 into 외출 — heating mostly stops.
- The button printed 온수 is the BATH boost (manual calls it 목욕) — it does not set the hot-water temperature; the 온수 KNOB does.
- 취침 (sleep) turns itself off after 5 h 30 min and goes back to room mode.
- The 45°C at the end of the heating knob is the top of the room-temp scale — you never need it except in the setup menu.
- If the 예약 knob is not at 0, the boiler may pause for hours (inferred).
¿Sale un código de error?
When 점검 lights, an error code shows in the number area. Press 전원 off/on to restart (3 tries max, then wait 5 min). If it returns, call 1588-9000 with the code.
Servicio técnico (coreano): 1588-9000
