켜기
- 1Press 전원 (bottom middle).
Alto&Daewoo DR-G21 영어 설명
A white Alto&Daewoo LCD panel: up/down pairs for heating (left) and hot water (right), and six icon buttons below.
각 버튼은 무슨 기능인가요?
- 1Heating up · 난방 ∧nanbang wiRaises heating temperature; in timer setting, adds an hour.
- 2Hot water up · 온수 ∧onsu wiRaises hot-water temperature.
- 3LCD screen · 룸콘표시부rumkon pyosibuShows heating temp (난방온도) and hot-water temp (온수온도), mode icons and a 1–24 h timer bar along the bottom.
- 4Heating down · 난방 ∨nanbang araeLowers heating temperature.
- 5Hot water down · 온수 ∨onsu araeLowers hot-water temperature.
- 6Heating · 난방nanbangPress: heating on/off. Hold: switch between room-air (실내온도) and boiler-water (난방물온도) control.
- 7Away · 외출oechulFreeze protection only: minimal heating when it gets cold.
- 8Hot water · 온수onsuHot water on/off.
- 9Timer · 타이머taimeoRepeating heat: 30 minutes of heating every 1–24 hours.
- 10Power · 전원jeonwonTurns the controller on or off.
- 11Quick hot water · 빠른온수ppareun onsuPre-heats so hot water arrives faster. Press about 1 minute before a shower; press again to cancel.
어떤 설정이 좋나요?
Room mode at 22°C if the controller is away from windows and heaters; otherwise water mode at 60°C. Hot water 43°C. Timer 3 h when out for the day.
어떻게 하나요?
실내 온도 맞추기
- 1Press 난방 so the heating icon is on.
- 2If the radiator icon shows, hold 난방 until the house-with-thermometer icon shows (room mode).
- 3Press 난방 ∧ / ∨ (left pair) to 22 (range 5–40°C). It blinks for 10 s, then saves.
온돌 모드
- 1Hold 난방 until the radiator icon shows (boiler-water mode).
- 2Press 난방 ∧ / ∨ to 60 (range 45–80°C).
며칠 집 비울 때
- 1Press 외출. The suitcase icon shows. The boiler only does freeze protection.
- 2In freezing weather leave a hot tap dripping slightly to protect the hot-water pipe (manual advice).
예약 설정
- 1Press 타이머. The current interval blinks on the bottom bar.
- 2Press 난방 ∧ / ∨ to choose the interval in 1-hour steps (1–24 h).
- 3Press 타이머 to confirm. The boiler then heats 30 minutes per interval.
- 4With 6 h or less it heats first; with 7 h or more it pauses first.
온수만 (여름)
- 1Press 난방 so the heating icon goes off. Keep 온수 on.
- 2Hot water works; no heating.
온수 온도 바꾸기
- 1Press 온수 ∧ / ∨ (right pair). Range 35–60°C, default 43. It blinks 10 s, then saves.
끄기
- 1Press 전원. (Turning both 난방 and 온수 off also powers down.)
화면 글자는 무슨 뜻인가요?
| 난방온도 | Heating temp | Room or boiler-water heating setting/reading. |
|---|---|---|
| 온수온도 | Hot-water temp | Hot-water setting. |
| house + thermometer icon | Room mode | Heating controlled by room temperature (5–40°C). |
| radiator icon | Water mode | Heating controlled by boiler-water temperature (45–80°C). |
| flame icon (연소) | Burning | Flame on. |
| suitcase icon (외출) | Away | Away / freeze protection on. |
| timer bar 1–24 | Timer | Dark segments = chosen interval. |
| Uo | Ignition failure | Check the gas valve is open / gas supply. |
| E1 | No water | Heating pipes short of water — check for a water cut, then call A/S. |
| E3 | Overheat | Water not circulating — check the floor manifold valves are open. |
이 모델에서 자주 헷갈리는 점
- Holding 난방 (not tapping) switches room vs water mode — a tap just turns heating off.
- In room mode the reading depends on where the controller hangs; drafts or sun make it wrong (manual note).
- Settings blink for 10 s before they save.
- Remembers its settings after a power cut.
- No 물보충 lamp: low water shows as error E1. If the 물보충 (water refill) light or code comes on, the boiler is low on heating water and will stop to protect itself. Do not open panels or valves. Message your landlord / building manager first, then call the A/S number. A light that keeps coming back usually means a leak.
에러가 떠요
Codes show on the LCD. Uo = no ignition (open gas valve); E1 = no water (check water cut, then A/S); E3 = overheating (open the floor manifold valves); E6 = gas leak; others call 1588-7339.
A/S: 1588-7339